KPW-1216 Open Arch Banding Machine for Cable & Hose Coils

Open-arch banding for coils and ring-shaped products

The KPW-1216 open arch banding machine is a tabletop film bander designed for a packing station where an operator needs to place a band around the local wall of a coil or another ring-shaped product. Its lift-open arch provides access for presenting a product with a centre opening. Cable coils, hose coils and tubing rings can be assessed according to their actual cross-section, flexibility and required band positions.

The important selection question is how the product sits around the arch and how the band crosses it. A large outside diameter does not describe that local banding space by itself. Send an annotated sample photo before choosing a configuration.

Measure the coil wall, centre opening and finished bundle separately

A coil bander must be checked against both access and the section enclosed by the band. The centre opening affects whether the product can be presented around the arch for through-the-eye coil banding, with separate bands placed at the required locations. The radial wall and stack height affect the banding cross-section. The outside diameter affects handling space around the machine. These dimensions should be shown separately in a quotation request.

The 120 mm limit applies to the local coil wall or wire-bundle section being banded. It is not a 120 mm limit on the outside diameter of the complete coil. The supplied specifications show a 120 × 180 mm window; KEEPWAY must also check the actual insertion clearance and product orientation with the sample.

What the openable arch and controls contribute

Access for ring-shaped products

The openable arch provides access for presenting a product around the banding area. It is useful when a ring-shaped item cannot be treated as a solid carton passing straight through a fixed arch. Confirm the loading orientation with the actual sample; a photograph of a coil alone cannot establish working clearance.

Final access and clearance at the openable arch and band guide are assessed with the proposed product orientation.

Film feeding, heat sealing and cutting

The banding mechanism feeds film around the local section, tensions the band, and forms a heat-sealed joint before cutting. The film structure, tension and sealing settings must be matched to the sample. A finished band should be checked for joint consistency, retention and the effect on the product surface.

The feed, sealing and cutting mechanism must be assessed with the actual band and product; no joint-strength rating or complete packing throughput is established by an illustration.

Settings that follow the sample

The supplied control-panel reference includes adjustment fields for band tension, sealing time and band length. These are setup variables for an approved product-and-band combination. Screen example values are not a universal operating recipe.

Use the approved touchscreen settings for the actual film and product rather than copying a value from an illustration.

Applications: assess the object and the required result

For cable and hose coils, assess the coil-wall section and whether the band holds the intended bundle during the required handling step. For tubing rings, include spring-back and surface requirements. Hanger stacks and wooden hoops illustrate other presentation shapes, but each needs its own sample assessment.

Assess each application with a sample check for size, weight, stiffness and the intended handling task.

KPW-1216 specifications and selection limits

The values below come from the supplied product material and the confirmed model, local-section definition and supply policy. They are reference specifications, not independent test results. Confirm the ordered configuration and sample fit in the quotation; the reference opening dimensions do not replace a clearance check with the actual product.

Film-band selection and configuration

The KPW-1216 is presented as a heat-sealing film bander. Select the band structure and dimensions against the machine configuration and the sample test. Do not substitute an ordinary tape simply because its nominal width looks similar. Include an existing film sample or its material specification when replacing a current banding process.

The quotation should state KPW-1216, the approved working space, film-band specification, ordered voltage and frequency, and included configuration. If a support arrangement or integration into another process is required, describe it as part of the project so its scope can be checked separately.

Approve a complete packing trial

1. Provide representative products, including the smallest and largest intended cross-sections.
2. Mark the required band positions and describe the finished bundle and handling step.
3. Assess presentation, band retention, sealed joint and surface condition with the proposed film.
4. Time the whole task, including loading, each band position, repositioning and unloading, before setting an output target.
5. Record the accepted film and settings for that sample and confirm the final configuration in the quotation.

Machine-cycle time and complete packing time describe different things. A multi-band coil may require several presentations and manual repositioning. Request a sample demonstration of the complete task when comparing output requirements.

Questions buyers often ask

Can the machine band a coil with a large outside diameter?

Outside diameter is one part of the check. Supply the centre opening, local coil-wall width, stack height, weight and a photo showing the intended band path. The product must fit around the arch in the proposed orientation, with sufficient insertion and handling clearance.

Does it rotate the coil and place every band automatically?

This page describes a tabletop banding station with operator presentation. If your process needs automatic infeed, rotation or transfer, provide the required sequence so a separate integration scope can be assessed.

Can it replace a carton strapper or an orbital wrapping machine?

Choose the process from the required pack. A local heat-sealed film band has a different task from heavy carton strapping, transport-load restraint or full-surface stretch wrapping. Send the intended handling and protection requirements before selecting equipment.

How many finished coils can one operator pack?

That depends on the sample, the number of bands and the presentation and handling sequence. A trial of the whole job provides a more useful basis than converting a single machine-cycle figure into finished coils per minute.

KPW-1216 coil banding demonstrations

These short demonstrations show operator presentation of the coil. Clip duration is not a machine-cycle or completed-coil production-rate specification.

Request a sample-based configuration

Send product photos, outside and inside dimensions, local banding cross-section, weight, band positions, surface requirements, target completed output, site supply and destination. If you already use film bands, include their material and dimensions. KEEPWAY can then assess the packing task and prepare a configuration for the actual sample.

Discuss your coil banding sample